Fortec 5680-BD Kevlar

Fortec #4550 LPL Structural Epoxy
Moisture insensitive, high modulus, high strength, structural epoxy resin.
PRODUCT SPECIFICATIONS:
Product Description
Fortec 4550 LPL Hi-Modulus Fiber Matrix is a 100% solids, solvent-free, two-component MOISTURE INSENSITIVE EPOXY. Fortec 4550 Fiber Matrix is a low viscosity epoxy for wetting and use with carbon fiber for structural repairs.
Advantages
- Easy mix ratio: 2 Parts A to 1 Part B by Volume
- Long Pot Life with rapid strength development
- Provides high early strength and excellent adhesion to most structural materials
- Insensitive to moisture before, during and after cure
- Low temperature cures – As low as 40oF (4oC)
Physical Properties
- Moisture Insensitive & low temperature cure
- #4550 LPL Fiber Matrix Structural Epoxy
Specifications
SPECIFICATIONS | |||
MIXING RATION | 2A to 1B | By Volume | |
COMPRESSIVE YIELD STRENGTH | ASTM-D-695 | ||
****40oF(4oC) | *75oF(24oC) | *90oF(32oC) | |
24 Hours PSI(Mpa) | 3200 (22 Mpa) | 3600 (25 Mpa) | |
3 Days PSI (Mpa) | 4000 (28 Mpa) | 9100 (63 Mpa) | 9600 (66 Mpa) |
7 Days PSI (Mpa) | 7200 (50 Mpa) | 10500 (72 Mpa) | 9600 (66 Mpa) |
TENSILE PROPERTIES | ASTM-D-638 | ||
14 Days Tensile Strength PSI | 6000 (41 Mpa) | ||
Elongation at Break | 2 – 4 % | ||
FLEXURAL PROPERTIES 14 DAYS | ASTM-D-790 | ||
Flexural Strength PSI | 7600 (52 Mpa) | ||
GLASS TRANSITION TEMPERATURE | ASTM-E-1356 | ||
2nd Run | |||
1st Run | >135oF (57oC) | ||
SHORE D HARDNESS | ASTM-D-2240 | 84 | |
POTABLE WATER | ANSI/NSF 61-1992 | Y/N | |
****INDICATES TEMPERATURE FOR CURING & TESTING |
Properties | ||
COLOR | Part A Resin | Straw |
Part B Hardener | Amber | |
Ad-Mix | Amber | |
PACKAGING | Available in 3 Gallon Units. Available in larger units on request. | |
CAUTION |
|
Temperature
Will cure at temperatures as low as 40oF(4oC), providing the temperature will be 40oF and rising during the next 72 hours. Epoxy materials should be stored at least 24 hours prior to use at 80oF(26oC),or higher. Epoxies stored below 60oF(15oC),will cause the epoxy to thicken substantially, making it difficult to properly blend the two materials and obtain a proper mating of resin and hardener. Protect from inclement weather and freezing. If product temperature falls below 50oF(10oC), it is recommended that a product temperature of 80oF(26oC) be obtained prior to using. Store dry at 40oF(4oC) – 100oF(38Co). Condition to 70oF(26Co) – 85oF(29oC) before using.
VISCOSITY: | Ad-Mix | ASTM-D-2393 | 700-900 cps |
GEL TIME: | 73oF (23oC) | approx. 100 minutes | |
TACK FREE TIME: | ***75oF (24oC) | ***90oF (32oC) | |
***AMBIENT TEMPERATURE | |||
NEAT BINDER | |||
Bond Strength,PSI | ASTM-C-882 | ||
2 Days (moist cure) Hardened concrete to hardened concrete or steel- 1200 min. (8.2 Mpa) | |||
Water Absorption 24 Hrs % | ASTM-D-570 | .08 % maximum |
CAUTION -FOR INDUSTRIAL USE ONLY:
FORTRESS FIBER MATRIX epoxies contain alkaline amines. Strong sensitizer MAY CAUSE SKIN SENSITIZATION or allergic response ranging from a mild wheezing to a severe asthmatic type attack. Avoid contact with skin or eyes. IN CASE OF CONTACT immediately wash skin with soap and water. Flush eyes with water and obtain medical attention. Wear protective clothing, goggles and barrier cream on all exposed skin.Provide adequate ventilation.